This heavy sidewalk graphic has a slip-resistant textured surface that stays slip resistant when wet and can be used in areas of heavy pedestrian traffic.
3M Sidewalk Graphic
This durable, slip resistant sidewalk graphic is designed for outdoor unsealed concrete and asphalt pedestrian surfaces. It's excellent for event advertising, special promotions, directional signage and information graphics. It is scuff and slip resistant, even when wet, holds up to the heaviest foot traffic, and is easy to clean. It's simple to apply and removes with little or no residue. Can be die cut. Available in widths up to 48".
This material is warranted for 90 days of use in pedestrian traffic areas. It can last much longer, but is only warranted for 90 days.
It's thick and durable, which also makes it easy to apply. It can go on both sidewalks and asphalt surfaces.
It's one of our most expensive materials. It's not designed for vehicular traffic. Since this material doesn't conform to the surface texture, it won't stick securely to extremely rough or dimensional surfaces.
It's excellent for outdoor sidewalk graphics.
Loose, damaged or wet sidewalk signs may cause a pedestrian to slip or trip and fall. To reduce the risk of slipping or tripping on sidewalk signs:
Some exterior surfaces are highly dimensional and the film adhesive may not have enough contact area to adhere properly to the surface.Condition of Surfaces3M Sidewalk Graphics will not adhere properly to loose, crumbling, contaminated, wet or damp surfaces. Ensure that:
- Properly apply only to unsealed outdoor surfaces (unsealed asphalt, unsealed concrete, paving bricks).
- Immediately remove or replace loose or damaged sidewalk signs. Do not attempt to repair or re-adhere.
- Upon completion of a pedestrian event on a roadway, remove the sidewalk sign before normal traffic resumes.
Note: Do not apply graphics late in the day when the surface temperature is likely to drop.Location of Sidewalk SignsSidewalk signs may be damaged by heavy equipment such as snow plows, shovels and power sweepers as well as by dragging heavy items across the top of the graphic. If possible, locate sidewalk signs out of the main stream flow of heavy equipment traffic. Minor edge chipping is unavoidable.Avoid placing the signs so the edges fall on seams in the mounting surface.Note: Sidewalk signs are specifically NOT designed for use where there is vehicular traffic.Sidewalk Surface PreparationThe adhesive on sidewalk signs cannot adhere properly to wet or damp surfaces. Therefore, never use any cleaning solvents or solutions, including detergent and water, to clean an application surface or to apply the graphic.Scrap off any grease, gum, weeds or grass found in expansion joints or other large particles from the application surface. Complete degreasing may not be possible.Clean the surface with a broom or a brush to remove all loose particles, dust, sand and gravel.SeamingA sidewalk sign can be seamed, but it must have an overlap of at least 3/8 inch. We recommend overlapping panels in the shortest direction, when possible.Multiple layers of film can cause bumps. Make sure there are no more than three layers of film at any intersection.Applying the DecalUse a stiff, nylon bristled brush for applying the film. The stiff bristles help work the film's adhesive into the irregularities of the sidewalk surface.A brush like the OXO Soft Works brush works well. It has 1 inch bristles in an oval base that is about 5 x 3 inches. It also has a comfortable handle. Suitable brushes are available in all housewares departments of discount and hardware stores.
- The surface is secure and in good condition.
- The surface has good internal bond.
- The surface is clean.
- The surface is completely dry.
- The surface IS NOT sealed. Sealed surfaces may result in extremely high adhesion that makes removal of the graphic difficult.
Remove or replace the entire sidewalk sign if there is any lifting from the pedestrian surface.Sidewalk signs should be mopped or brushed periodically for optimum skid resistance and appearance.The structured surface of the overlaminate may pick up dirt. To clean the graphic, use a stiff, nylon-bristled brush or a light duty automatic cleaner and a cleaning agent such as Simple Green®. Follow the manufacturer's instructions for use. Do not use any cleaning agent that contains solvents, which can erode the sign material.Never pressure wash sidewalk signs. Doing so forces water under the graphic, causing the edges to lift and curl.If a sidewalk sign containing an overlap has shrunk, revealing some of the adhesive, it may be cleaned by spraying the exposed adhesive with 3M Industrial Cleaner. Allow the cleaner to sit for one minute, and then wipe the surface with a rag or use a stiff, nylon-bristled brush to clean the surface and remove any adhesive.Removal Instructions
- The application surface must be clean and completely dry.
- Film must be applied at a minimum surface temperature of 70°F (21°C). Heat helps bond the adhesive; therefore, the warmer the temperature, the better the bond.
- Do not use an application tape.
- Position the graphic on the clean, dry surface. Expansion joints can be used to align the graphic, but always position the graphic so none of its edges start or end on an expansion joint. Bridge the film over grouting, seams, stone edges and expansion joints. DO NOT push the graphics into those areas.
- Make a hinge: peel back one edge of the liner to expose the adhesive and apply that edge to the substrate. Using firm pressure and a stiff, nylon-bristled brush make one stroke across the top of the graphic. Note: Do not smooth the graphics with your hands because this entraps air.
- Lift the opposite end of the graphic from the hinge. While keeping the graphic raised up, peel back about 12 inches of liner. Working from the center out to the edges of the graphic, use the brush, firm pressure and overlapping strokes to adhere that part of the graphic to the surface. Continue in this manner until the graphic is completely applied.
- The application is not finished until you re-brush the edges and the corners. This ensures a good edge seal. Re-brush all the edges of the graphic, using firm, circular brush strokes. This works the adhesive into the application surface to provide better bonding.
- Remove sidewalk signs by lifting one edge and pulling it off at a sharp angle-about 135 degrees-with smooth, even tension. A scraper, such as a putty knife, may be used to lift the edge, if needed. Some adhesive residue may remain on typical outdoor surfaces.
- Usually, it is easier to remove the graphic during the coolest part of the day. It may also be helpful to cut the graphic into strips about two inches wide and then pull off each strip. Use a razor blade with a safety handle. Note: Because the area under the graphic initially will be cleaner than the surrounding surfaces, you may notice a shadow of where the graphic was placed. This is normal.